Tasks for which I do not need to buy anything (In the relative order I want to complete them in)
- build rear brake calipers
- make front wheel wells
- mount external filter setup
- mount oil cooler
- Figure out intercooler and radiator ducting
- fit gas tank
- repair old damage driver side rear fender
- hydroform/make bulge in hood
- attach bulge to hood
- lube chassis points
- figure out intercooler piping
- heater air feed
- mount heater box
- wire car
Tasks which will cost
- figure out coolant hoses
- have exhaust ceramic coated
- run fuel lines
- run brake lines
- turbo oil and coolant feeds
- gauges
- redo seats
- carpet interior
- battery
- seatbelts
- cockpit roll bar
- throttle cable
finish welding
- finish welding around front wheel arches
- finish welding around rear wheel arches
- close all pinhole gaps
- Finish welding edges of body to new metal
- clean up tall welds in interior
- improve welds on seat mounting rails
- finish welding floors
shopping list
- heater
- grade 8 locking fasteners
- intake bolts
- stand alone wiring harness
- quest alternaor
- maybe new water pump
- MGB lamps
- backup lights
Completed
- 05-21-2016 – cut hole in hood
- 03-20-2015 – mount charcoal filter
- 11-30-2014 – relocate throttle body
- 11-07-2014 – repair rust on front fender
- 07-04-2014 – make rear parcel shelf removable
- 03-24-2014 – fit intercooler
- 03-24-2014 – figure out front sheet metal mounting
- 01-19-2014 – rebuild output bearings and seals – rear end
- 09-14-2013 – mount water neck relocation (replace with G20 outlet)
- 09-04-2013 – get clutch
- 08-10-2013 – resurface flywheel
- 08-10-2013 – modify engine outlet
- 08-10-2013 – modify intercooler
- 07-28-2013 – make intercooler bulge and fit to splash pan
- 07-21-2013 – work on dash
- 06-26-2013 – rebuild outer wheel bearings/mount hubs
- 06-09-2013 – modify rear end carrier for more clearance
- 06-09-2013 – adjust wastegate opening pressure
- 06-08-2013 – rebuild turbo
- 05-26-2013 – mount oil bypass
- 05-25-2013 – replace pan
- 05-05-2013 – raise front spring mounts by .25 inch
- 03-10-2013 – lower whole front end by 1 3/8 inch
- 01-19-2013 – finish rough in of front flare ends
- 01-15-2013 – Install shorter front wheel studs
- 01-05-2013 – fit fan
- 03-12-2012 – fit radiator
- 02-13-2012 – redrill rear hubs for 5×4.5
- 02-12-2012 – attach rear fender extensions
- 12-26-2011 – close rear wheel wells
- 12-04-2011 – Cut out extra metal on rear fenders
- 10-22-2011 – Cut out extra metal on front fenders
- 10-23-2011 – cut front swaybar arms
- 10-29-2011 – close open tube on front of car
- 10-29-2011 – make cover plate for rear shifter location
- 10-29-2011 – clearance shifter relocation rod
- 11-10-2011 – run exhaust to muffler
- 11-12-2011 – make locking screw location on steering
- 11-19-2011 – build exhaust mounts
- 11-19-2011 – attach muffler
- 11-20-2011 – finish steering
Bought
- external filter setup
- fan
- oil cooler
- gas tank